微波耦合铁碳微电解预处理石化废水的试验

采用微波耦合铁碳微电解技术对石化废水进行预处理,并对预处理前后水样中有机物的变化进行分析。结果表明,原水CODCr为10 500 mg/L,在废水pH值为3、铁碳投加量为20%、微波功率为700 W,经微波辐射5 min处理后,出水CODCr为2 370 mg/L左右,COD去除率稳定在77%左右,提高了废水的可生化性。GC-MS和三维荧光分析结果均表明,微波耦合铁碳微电解处理后,试验废水中有机物的数量及浓度大幅降低。结合后续生化处理,可以达到三级污水综合排放标准(GB 8978-1996)。微波耦合铁碳微电解可作为石化废水的有效预处理方法。     

高盐高有机制药废水污泥电渗透高干脱水

为研究高盐高有机制药废水污泥的电渗透脱水效果，深入认识化学污泥的电脱水过程，本文采用电渗透高干脱水技术对经抽滤脱水的高盐高有机制药废水化学污泥进行深度脱水，考察了泥饼初始pH的改变对污泥电渗透高干脱水过程中阴阳极污泥的含水率、电流、电导率、pH、zeta电位与能耗的影响，验证了对高盐高有机制药废水污泥实行电渗透高干脱水的可行性，解析了化学污泥电渗透脱水过程的机制。结果表明，泥饼pH为2、3、4时，zeta电位为正值，电渗流反向流动，无法脱水；pH增至5时，zeta电位为负值，电渗流从阴极脱除，污泥含水率从53.2%降至44.8%，脱水效果最好；但pH增至6时，脱水量有所降低。污泥电导率随pH的增加而降低。pH为5时初始电流最大。脱水15min时，即污泥含水率降至45.5%时，能源利用率最高。     

一种大型复杂构件加工新模式及新装备探讨

大型复杂构件是航空航天、能源、船舶等领域装备的核心结构件，此类构件通常具有尺寸大、形状复杂、刚性弱等特点。传统“分体离线加工-在线检测”模式存在工艺不稳定、过程复杂、柔性差、周期长等问题，以龙门式多轴数控机床加工为代表的“包容式”加工模式，难以适应大型复杂构件的高效高质量加工制造需求。提出一种基于移动式和吸附式机器人的多机协同原位加工新模式，通过多机器人系统自主寻位、精确定位加工与加工质量原位检测，实现大型复杂构件多安装面并行铣削、制孔与打磨等作业。多机器人系统包括移动式混联机器人、吸附式并联机器人、移动式串联铣削机器人、移动式双臂加工机器人和移动式打磨机器人。构建多机协同原位加工模式，需要揭示多机器人协同原位加工行为与大型弱刚性结构件质量控制的交互机理，面临着本体、测量、工艺和集成四个方面的挑战，需要设计高灵活、高刚度的移动式和吸附式加工机器人，解决移动机器人自主准确寻位和超大结构件原位高精检测难题，攻克加工变形误差在线补偿和振动抑制技术，通过集成实现多机协同高效高精加工，为大型复杂构件的高效高质量制造提供创新技术及装备，并实现此类构件制造核心技术及装备自主可控。     

磁性纳米材料处理含铀废水的研究进展

磁性纳米材料具有较强的化学稳定性、可再生回收、良好的吸附性能和易于分离等优点，在去除水溶液中的铀酰离子方面有广泛的应用前景。然而，磁性纳米材料也存在易团聚、易氧化等不足，通过表面修饰或改性等方法可改善其不足，提高其对废水中铀酰离子的去除能力，改善其吸附效果。本文通过总结近年来的相关研究资料，概括了磁性纳米材料的种类，归纳总结并比较了不同种类磁性纳米材料对含铀废水的去除能力及优势与不足，探讨了磁性纳米材料在含铀废水处理中的应用并对其机理进行了分析，阐述了磁性纳米材料去除溶液中铀酰离子的影响因素，简述了目前磁性纳米材料在处理含铀废水中有待解决的问题，并对其在分离放射性元素方面的应用前景进行了展望。     

Experimental investigation of Al2O3–MgO hot hybrid nanofluid in a plate heat exchanger

Exergy–energy analysis of the plate heat exchanger is experimentally performed with different Al₂O₃–MgO hybrid nanofluid (HyNf) as a hot fluid. There were six combinations of fluids, namely, deionized (DI) water, ethylene glycol–DI water brine (1:9 volume ratio), propylene glycol–DI water brine (1:9 volume ratio), base fluids and their respective Al₂O₃–MgO (4:1 particle volume ratio) HyNfs of 0.1% total volume concentration. The effects of different flow rates and hot inlet temperatures on the heat transfer rate, heat transfer coefficient, pump work, irreversibility, and performance index (PI) are investigated. It is witnessed that the heat transfer rate, heat transfer coefficient, pump work, and irreversibility enhances with the flow rate and nanoparticle suspension. While the PI declines with a rise in the flow rate, the heat transfer rate, heat transfer coefficient, PI, and irreversibility rise up maximum for MgO–alumina (1:4) DI water HyNf upto 11.8%, 31.7%, 11.1%, and 4.05%, respectively. The pump work enhances upto 1.6% for MgO–alumina (1:4)/EG–DI water (1:9) HyNf.     

Experimental investigation on the mechanical,structural and thermal properties of Cu–ZrO2 nanocomposites hybridized by graphene nanoplatelets

Hybrid Cu–ZrO₂/GNPs nanocomposites were successfully produced using powder metallurgy technique. The effect of GNPs mass fraction, 0, 0.5, 1 and 1.5%, on the mechanical and electrical properties of the produced hybrid nanocomposite was investigated while maintaining ZrO₂ mass fraction constant at 5%. High-energy ball milling was applied for mixing powders followed by compaction and sintering. The morphological analysis of the produced powder showed acceleration of Cu particles fracture during ball milling with the addition of GNPs up to 0.5% with noticeable reduction of agglomeration size. Moreover, the crystallite size of Cu–5%ZrO₂/0.5%GNPs hybrid nanocomposites revealed smaller crystallite size, 142 nm, compared to 300 nm for Cu–5%ZrO₂ nanocomposite. Additionally, the hybrid nanocomposite with 0.5% GNPs shows homogeneous distribution of both reinforcement phases in the sintered samples. The compressive strength increased with the GNPs content and reached 504.6 MPa at 0.5%, 31% higher than the Cu-5%ZO₂. The thermal conductivity had the maximum value at 0.5 wt%GNPs and reached 345 W/m k. The results provide efficient manufacturing process for high strength and good conductivity hybrid nanocomposites, which is applicable in many structural applications such as heat exchange purposes.     

海藻化工以氢氧化钙作为钙化剂的新型钙化工艺研究

研究了海藻化工中以氢氧化钙作为钙化剂的新型钙化工艺,使用氢氧化钙+氯化钙作为褐藻酸钠的钙化剂替代传统的单一氯化钙。确定的双钙钙化工艺条件：每升褐藻酸钠胶液（褐藻酸钠质量浓度为2.5 g/L）,添加氯化钙溶液29.0 mL（质量分数为5%）,添加氢氧化钙溶液13.75 mL（质量分数为5%）,复合钙化剂中氯化钙与氢氧化钙物质的量比为1.19∶1。与传统工艺相比,新型钙化工艺褐藻酸钠的产率未有明显变化,得到的褐藻酸钠粘度稍有降低,粘度由275.1 mPa·s降低至241.3 mPa·s;氯化钙使用量降低40%以上,总钙添加量减少19%。双钙钙化工艺实现了对钙化废水的再利用,废水中钙质量浓度经处理由483 mg/L降到20 mg/L左右,电导率由6.84 mS/cm降至4.28 mS/cm;经脱钙处理的钙化废水回用后对产品褐藻酸钠的产率和粘度没有显著影响。新工艺操作简单,不仅有效减少了钙化废水中离子的引入,同时可以实现低成本地脱钙,脱钙后的废水可以作为冲稀水回收利用,减少了水资源的消耗,为海藻化工行业的减排提供了一条新的工艺途径。     

微电解Fenton法处理有机废水可行性研究

采用微电解Fenton法处理硫铵酯-苯甲羟肟酸-苯胺黑有机废水。考察了初始pH值、铁屑及活性炭投入量、曝气量、H₂O₂用量、催化剂MnO₂加入量和反应时间对废水COD、NH₃-N和色度去除率的影响。最佳条件为:初始pH=3、铁屑用量70 g/L、活性炭用量80 g/L、H₂O₂用量7 mg/L、MnO₂用量8.0 g/L、曝气量500 mL/(min·L)、反应时间20 min,此时废水COD、NH₃-N和色度的去除率达88.21%、93.57%和98.68%。通过多因素正交实验确定了影响COD、NH₃-N和色度去除率的因素强弱顺序为:铁屑投入量=活性炭投入量>H₂O₂用量>pH值>MnO₂用量。     

基于混合时间序列卷积神经网络的轴承故障诊断

在传统滚动轴承故障诊断中,绝大多数方法采用了从振动信号提取特征的诊断模式,但是这种模式必然会使原始信号降维进而导致故障信息的丢失。卷积神经网络(CNN)通过权重共享和稀疏连接直接对原始信号进行操作,实现自适应特征提取,最大化保留故障信息。受CNN原理启发,开发出了一种基于工业振动信号特征的新型诊断框架,称之为混合时间序列CNN(HTS-CNN)。首先,利用估计总体比例的方法自适应确定模型训练样本数目;其次,通过对时间序列片段进行随机组合的方式,使模型能够提取非相邻信号特征;最后,利用Softmax激活函数在模型输出端执行多分类任务。通过对凯斯西储大学及CUT-2平台轴承数据进行分析,实验结果表明:该方法能够准确、有效的对滚动轴承故障进行分类。     

Study on the performance of syntactic foam reinforced by hybrid functionalized carbon nanotubes

Hollow glass microspheres (HGMs)/epoxy syntactic foam were reinforced by hybrid functionalized carbon nanotubes that were synthesized by simultaneous covalent and noncovalent functionalization of carbon nanotubes. The effect of hybrid functionalized carbon nanotubes on density, mechanical properties, and water absorption of HGMs/epoxy syntactic foam was studied. The study indicated that the dispersion of carbon nanotubes in epoxy resin can be improved by hybrid functionalization. The compression strength of syntactic foam reinforced by hybrid functionalized carbon nanotubes was significantly enhanced. The maximum compressive strength of syntactic foam corresponding to chitosan modified carbon nanotubes approached 60 MPa. Hybrid functionalized carbon nanotubes had little effect on the water absorption ability of syntactic foam, and was less than 1%. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48586.